Alle categorieën
EN

Home>Nieuws

Montage van klembusverbinding

Tijd: 2022-07-14 Hits: 9

Assembly of sleeve type pipebeslag

Preinstallation the most important link of the preinstallation of the sleeve type pipebeslagheeft direct invloed op de betrouwbaarheid van de afdichting. Speciale voorlopers zijn over het algemeen vereist.Montages with small diameter can be preassembled on the bench vice. The specific approach is to use abeslag als de matrix, de moer, klembus kan worden gedrukt op de pijp. Er zijn voornamelijk huls type door pijpbeslag, mouwtype einde door aansluitkop, mouwtype driewegbuisbeslagand other types. The author found that even for a batch of goods from the same manufacturer, the depth of the conical hole on thebeslag body is often not the same, resulting in leakage, and this problem is often ignored. The correct way is to use what kind ofbeslag body is used at one end of the pipe, and the correspondingbeslag einde is vooraf geïnstalleerd met hetzelfde type beslag, om lekkageproblemen zoveel mogelijk te voorkomen.

Het uiteinde van de pijp moet vlak zijn. Nadat de pijp is gezaagd, moet deze gelijkmatig worden gepolijst op een slijpschijf en andere gereedschappen, en de bramen moeten worden verwijderd, gereinigd en gereinigd met hogedruklucht voor gebruik.

 Tijdens de voorinstallatie wordt de coaxialiteit van de buis en debeslag body should be kept as far as possible. If the pipe is too deviation, it will also cause sealing failure.

53d5a362c23c9ed7ab3ced12ac4a330e

The pre-installed force should not be too ambassador that the inner edge of the sleeve is just embedded in the outer wall of the pipe, and the sleeve should not be obvious deformation. When connecting pipes, assemble according to the specified tightening force. The clamping force of the 6-1 sleeve is 64-1 15N, 16ф MMR 259N, ф18mm for 450N. If the jacket deformation is serious in pre-installation, the sealing effect will be lost.

Do not add sealant and other fillers. Some people in order to achieve better sealing effect, in the card sleeve coated with sealant, the sealant was rushed into the hydraulic system, resulting in hydraulic components Yin nihole blockage and other faults.

When connecting the pipe, the pipe should have enough deformation allowance to avoid the pipe being subjected to tensile force.

When connecting the pipeline, it should avoid being subjected to lateral force, which will cause lax sealing if the lateral force is too large.

When connecting the pipeline, it should be good once and avoid multiple disassembly, otherwise it will make the sealing performance worse.

50084626c49d5e22c5d5259b20bdca4a

Installation of sleeve type pipe beslag

(1) Het beitsen van de buizen zoals vereist in Hoofdstuk 9 moet als eerste worden uitgevoerd;

(2) Snijd de buis op de gewenste lengte met een zaagmachine of speciale buissnijmachine en andere gereedschappen, het is absoluut niet toegestaan ​​om de buis op te lossen (zoals vlamsnijden) of te slijpen; Verwijder bramen aan de binnen- en buitenkant van het uiteinde van de buis, metaalspanen en vuil; Verwijder het antiroestmiddel en vuil van de buisbeslag; Tegelijkertijd wordt de rondheid van de pijp gewaarborgd;

(3) de moer, de huls is in de pijp gezet, de voorste rand van de huls (kleine uiteinde) van de pijpmonding minimaal 3 mm, en dan de pijp in debeslag body cone hole, top until;

(4) Draai de moer langzaam vast, draai de buis totdat deze niet meer beweegt en draai de moer vervolgens 2/3 tot 4/3 keer vast;

(5) Open en controleer of de mantel in de pijp is gesneden en of de positie correct is. De mantel mag geen axiale beweging hebben, maar een kleine rotatie;

(6) Draai de moer vast nadat de inspectie is geslaagd.